JetDielineGlue flap
Width of the glue flap used to glue the blank into a tube. The material requires a minimum width.
Corrugated shipping boxes / JETDIELINE
Carry box with hand hole
Corrugated carry-handle box with snap-lock bottom. Two fully overlapping lid flaps have aligned handle cut-outs and are glued across their surfaces; an additional handle is not part of the construction.
CutFold
Drag to rotate
Interactive 3D fold view
03 / BOX
Simplified display model without material thickness, not to scale.
The 3D view is not available in this browser. The image shows the folded shape.
- Template ID
corrugated.handle- Construction
- Corrugated shipping boxes
- Current template version
- V1
- Dieline preview version
- V1
How the shape is constructed
Corrugated box with snap-lock bottom, whose outer top flaps fully overlap and are glued; both flaps have a central handle cut-out for the hand – for carrying without an additional handle.
How it is assembled
Glue the glue flap, erect the box and close the snap-lock bottom (side flaps, flap with tongue, flap with nose under the tongue). After filling, fold in the upper inner flaps, lay down the back's outer flap and then the front's over it so that the handle cut-outs align, and glue across their surfaces.
Material and grain direction
Flute direction parallel to the height: stable when stacked (check with the test print shop).
Test fit, folding and closure on a sample made from the intended material. Confirm material thickness, grain direction and production steps with your printer.
Dimensions of the illustrated example
400 × 220 × 220 mm40 × 22 × 22 cm15.75 × 8.66 × 8.66 in / ″
Length: 400 mmWidth: 220 mmHeight: 220 mm
Inside dimension
These dimensions describe the preview, not a fixed packaging size. The app recalculates the dieline for your own dimensions.
What to consider for this construction
Glue flap angle
Angle at the ends of the glue flap; makes folding and erection easier.
Flap gap
Gap between adjacent flaps or walls; at least about the material thickness.
Bottom flap overlap
Overlap of flaps 3 and 4 outside the closure.
Locking tab length
Length of the tab on flap 4 that engages under the tongue of flap 3.
Frequently asked questions
Is the handle an attached part?
No. Both upper outer flaps have an oblong slot cut-out. After closing, the cut-outs align and form the hand opening. The lid flaps are glued across their surfaces. A plastic handle or additional carrying strap is not part of this model and cannot be promised from it.
What load can the box carry?
The catalogue and starting profile do not state an approved load capacity. Handle bridges, corrugated board, adhesive bond and snap-lock bottom jointly determine load capacity. The starting run checks geometry and manufacturability. Carry out load tests with the actual contents and have the production partner confirm the construction before stating a load capacity.
Why is a longer handle not always possible?
The handle must sit between the inner flaps without removing the remaining bridges. gripLength.geometric.betweenInnerFlaps accounts for this area. The table range from 60 to 200 mm is therefore only the general range. For a short box, even a value within it may be invalid because of the actual geometry.
Related features
Templates and dimensions
Find the right packaging shape and fit it to your product
Designer
Design the artwork directly on the real dieline
Checks
Spot problems before you pass on files
Export and handover
Files your printer can trace
Related templates
Corrugated sheet with creases
Rectangular corrugated sheet with zero to three evenly spaced creases. Without a crease, it serves as a flat layer pad; folded, it forms an angle, U-profile or wrap around a product.
corrugated.sheetView template
Slide sleeve
Corrugated sliding sleeve with glue flap and open ends. Thumb cut-outs at both ends of the top make sliding out an inner component easier. The template calculates only the sleeve.
corrugated.slideView template
Self-seal shipping box
Corrugated shipping box with fully overlapping lid flaps, self-seal closure and tear strip. The bottom is closed with adhesive tape as on a slotted box; the upper closure has an adhesive strip and opening aid.
corrugated.shipper.selfsealView template
Mailer with locking tabs
Corrugated mailer with double side walls and an external tuck closure. The lid locking tabs engage through oblong holes in the front wall; the construction is erected without gluing.
corrugated.mailer.lockView templateYour product. Your dimensions. Your design.
With JetDieline, choose a suitable template, adjust its size, and place text, logos, and images directly on your packaging.
Try your dimensions
Ask about the app