JETDIELINE / Templates

Food

Compare openings and closures for your food product. Check direct-contact material, moisture and grease resistance with the manufacturer.

47Constructions, components and assemblies

Individual components are shown separately. Different sizes and stored template versions are not additional packaging shapes.

carton.tuckend.straight

47 visible entriesView the full catalog ↗

Straight tuck-end carton

Blank, creases, and flaps are calculated from inside dimensions. The result is an artwork PDF, production dieline, and production sheet for the print shop.

carton.tuckend.straightView template

The top tuck flap is attached to the front, the bottom one to the back. The reverse tuck end carton calculates its walls, dust flaps, and closures from the inside dimension. The dieline shown comes from Version 3 with the hanging hole disabled; artwork, production dieline, and report can be exported together in the technical core.

carton.tuckend.reverseView template

Regular slotted container

The regular slotted container connects four walls, a glue flap, and four flaps each at the top and bottom. Its outer flaps meet in the middle; the reference is similar to FEFCO 0201.

corrugated.rscView template

Sleeve

The sleeve surrounds a product with four walls and remains open at both ends. Length and width describe the cross section; height denotes sleeve length. The dieline shows version 1 with finger notches on the front. Material thickness, glue flap, and notch position remain part of the calculation rather than simple scaling.

carton.sleeveView template

Folding tray with locking corners

An open corrugated tray with double end walls and locking corners. The blank is erected without adhesive; this page shows our own V2 construction with B flute.

corrugated.trayView template

Folding carton with crash-lock bottom

The pre-glued crash-lock bottom closes as the body is erected. Dust flaps and a tuck flap close the top of the folding carton; bottom gluing is part of the production workflow.

carton.crashlockView template

Folding carton with snap-lock bottom

The snap-lock bottom closes with four interlocking flaps. Two side flaps lie inside; a tab at the back tucks under the tongue of the front flap. Version 1 combines this bottom with a tuck lid. The calculated example uses folding carton board 400 g/m² and shows the flat dieline with creases and bottom slits.

carton.snaplockView template

Rectangular label

Rectangular label with selectable corner radius; dieline with bleed and safety zone from the production profile.

label.rectView template

Round label

Circular label; the diameter is both width and height.

label.roundView template

Oval label

Oval label as an ellipse with width and height as axes.

label.ovalView template

Wraparound label

Wrap label for cylindrical bottles and cans: length from circumference (or diameter) plus overlap; the front viewing area and overlap are marked as annotation lines.

label.wrapView template

Wraparound label for tapered cups

Wrap label for tapered cups and cans as a cone blank (annular sector) with a constant-width glue strip.

label.tapered.wrapView template

Paper band

Paper wrap band around a round body or a stack: length from circumference plus ease allowance and overlap; the overlap at the beginning is the glue area.

band.wrapView template

Belly band for boxes

Paper belly band around the four walls of a box, with creases at the edges and a glue flap; crease-to-crease dimensions from the box's outside dimensions plus material thickness.

band.bellyView template

Wrap for can or tube

Calculate the wrap from diameter or circumference, height, and overlap. Slit turn-ins are added for a cardboard tube; for a can, you can disable both. The drawing shows the blank with starting values, not a finished can or confirmed fit.

tube.wrapView template

Lid or base disc with tabs

The lid or base disc has glue flaps around a circular crease line. The starting dimensions are the inside diameter of the tube wall and its height. The parametric dieline shows the disc as an individual component; check a matching tube wall and assembly separately.

tube.discView template

Flat bag

The flat bag consists of front and back with two glued side seams and a bottom fold. Enter bag width and height as outside dimensions. An optional flap on the back closes the opening; the dieline shows its effect on the paper blank.

bag.flatView template

Gusseted bag with block bottom

The side-gusset bag has a glued longitudinal seam and a block bottom made of flaps, ears, and triangles. You set bag width, gusset depth, and height. The inside dimension shown is converted into crease-to-crease dimensions using the material profile; the flat dieline also includes the bottom overlap.

bag.gussetView template

Tray with glued corners

A base, four walls, and glued corners form the open folding tray. This page shows V2 with an optional window; the window remains disabled in the starting example.

carton.tray.gluedView template

Tray with locking corners

Unglued folding carton board tray: front and back walls with corner flaps, double end walls with a rollover; tabs on the inner wall tuck into slots in the bottom.

carton.tray.lockedView template

Dispenser carton with tear-out window

Reverse tuck end carton with a perforated tear-open window in the front and a thumb notch as an opening tab; after opening, contents are removed individually.

carton.dispenserView template

Hinged-lid carton

The hinged lid sits on the back wall and lays its front wall over the outside of the front. A lid flap inserts through a slot in the front; a tuck bottom closes the base. The page shows version 2 with the hanging hole disabled. The technical core calculates lid overhang, flaps, and creases from the chosen dimensions and material profile.

carton.hinged.lidView template

Tuck-end carton with window

The window carton combines straight tuck closures with a front cutout. Choose a rectangle with corner radius or an oval and leave room for the film margin and bridges. The shown version 2 starts with a rectangular window and no hanging hole. The dieline provides the construction; window film is patched separately on the inside.

carton.windowView template

Gable box with handle

The gable carton combines a tuck bottom with a gable roof and glued handle flaps. The page explicitly shows version 1 with handle hole, roof panels, and gussets. The entered height describes the body; gable and handle are added using separate parameters. The calculated dieline is a basis for the folding sample, not proof of load capacity.

carton.gableView template

Pizza box

The pizza box is formed from one blank with double side walls, locking corners, and a hinged lid. Inside dimensions determine the space for the pizza; ventilation slots and locking tabs are separate parameters.

carton.pizzaView template

Hinged-lid tray (clamshell)

The clamshell tray combines a base with glued corners and a lid hinged to the back wall. You choose a tuck flap or tab-and-slot closure and calculate either from inside or outside dimensions.

carton.tray.hingedView template

Takeout box

The takeout box has outward-sloping front and back walls, glued corners, and a folding lid with a tuck flap. Inside width and outside width have different reference points.

carton.takeoutView template

Fries scoop

The French fry scoop remains open at the top and has a taller back wall, a lower front, and downward-sloping sides. Front width, depth, and back wall height form the inside dimensions; front height is a separate parameter.

carton.friesView template

Popcorn box

The popcorn box is open at the top and has four outward-sloping walls, a side seam, and a glued bottom. Length and width describe the top opening; the bottom is smaller.

carton.popcornView template

Sandwich wedge

The sandwich wedge forms a triangular prism from a bottom and two sloping sides, a glued-in back, and a hinged lid. Inside dimensions describe baseline, prism thickness, and triangle height.

carton.wedgeView template

Overlap slotted container

An adjustable strip connects the outer flaps at the top and bottom. The template calculates flap lengths, material layers, and blank from box dimensions and the desired overlap.

corrugated.rsc.overlap.outerView template

Slotted container with meeting inner flaps

The inner flaps meet in the center and close the opening. Outer flaps with an adjustable gap sit above them; our construction calculates both flap layers together.

corrugated.rsc.innerfullView template

Carry box with hand hole

Corrugated carry-handle box with a snap-lock bottom. Two fully overlapping lid flaps have aligned handle cutouts and are glued over their full area; an additional handle is not part of the construction.

corrugated.handleView template

Slotted container with crash-lock bottom

The corrugated box is preglued at the factory and supplied flat. The crash-lock bottom closes during erection; the top can have meeting flaps, fully overlapping flaps, or an open edge.

corrugated.autobottomView template

Flat pouch (3-side seal)

This template calculates the print mask for a flat pouch with a three-side seal. Front and back share one print sheet with a bottom fold. Side and top seams are seal zones; optional additions include a zipper, tear notch, and hanging hole. The drawing is not an approved die-cutting contour for film.

pouch.flatView template

Stand-up pouch (Doypack)

The stand-up pouch receives a print mask comprising the front, inserted W-shaped bottom gusset, and back. Side seam, top seam, Doyen corners, and zipper band remain documented as seal zones. Pouch width and height are outside dimensions; the bottom gusset is a separate parameter. The calculated print sheet does not yet confirm standing stability.

pouch.standupView template

Spout pouch

The spout pouch print mask adds a sealed-in spout to the stand-up pouch. Choose the top right corner or the center of the top edge and enter the inside diameter. The spout's boat-shaped flange is part of the seal zones; the drawing documents its position, not confirmed component fit.

pouch.spoutView template

Seal-end carton

Folding carton with a side seam and glued top and bottom closures (Seal End) in place of tuck flaps: outer flap at the front, inner flap at the back, dust flaps at the sides. For pharmaceuticals and food; opened by tearing.

carton.sealendView template

Pallet display (shell)

Shell of a corrugated pallet display for a quarter or half pallet: tube of four walls with glue flap, large shelf opening in the front between plinth and top header (advertising area). The shelves are stacked in from above.

corrugated.display.palletView template

Pallet display shelf

Stackable corrugated shelf: base with raised rims, open corners and a low front lip as price rail. Dimensions: inside cross-section of the shell × shelf height.

corrugated.display.pallet.shelfView template

Egg carton with hole-deck insert

Folding carton tray with glued corners, hinged lid and an integrated hole deck for 6, 10 or 12 eggs. The construction uses a hole deck rather than molded pulp cups. Check egg size, retention and transport on a filled sample.

carton.eggView template

Cake box

Box for cakes and tarts with a tuck bottom, a split lid of two roof halves and a carry handle made of two handle panels with handle holes; optional window in the lid halves or in the front. Starting material E-flute microflute, start sizes for cakes Ø 24, 26 and 28 cm.

carton.cakeView template

Shelf display (shelf-ready tray)

Shipping and shelf packaging in one: tray with four walls of equal height and glued corners, a U-shaped tear-off perforation with a thumb notch in the front wall. After tearing off, a low front and side lands remain; optional header on the back wall (straight, rounded or arched). Starting material B-flute.

carton.display.shelfView template

Your product. Your dimensions. Your design.

With JetDieline, choose a suitable template, adjust its size, and place text, logos, and images directly on your packaging.

Try your dimensions

Ask about the app

Food

Explore by packaging shape or application

Your product. Your dimensions. Your design.